A downspout installation comes down to four decisions: where the downspouts go, what size they are, how they are fastened, and where the water ends up. Get those right and the gutter carries roof water away from your foundation. Get one wrong and the water lands beside your basement wall. At Revive Exteriors (Lic. #262500123, revivemihome.com), we install seamless gutters across Northern Michigan, and this guide walks through the whole job so you can judge any plan, ours or anyone else’s.
TL;DR
- Put a downspout at the low end of every gutter run, roughly every 20 to 50 feet, and at outside corners when you can.
- Fasten the downspout to the wall with straps about every 6 to 8 feet, overlap the joints, and seal the gutter outlet.
- Discharge water at least 5 feet from the foundation, or 10 feet if you pipe it underground.
- National average for installing downspouts is about $670, so slope, length and material matter more than the headline figure.
- For Traverse City, Petoskey, Alpena and the rest of Northern Michigan, call Revive Exteriors at (866) 466-3351 for a complimentary inspection.
Table of Contents
- What a downspout actually does
- Step 1: Decide how many downspouts you need and where
- Step 2: Choose the size and material
- Step 3: Cut the outlet in the gutter
- Step 4: Set the slope toward the downspout
- Step 5: Build the downspout run
- Step 6: Hold the downspout to the wall
- Step 7: Send the water away from the house
- What downspout installation costs
- Why hire an installer for this
- Get your downspouts planned and installed
- FAQ
- Sources
What a downspout actually does
A gutter collects water from the roof edge. The downspout is the vertical pipe that carries it down and out. The gutter itself rarely fails first. The Roofing Brief’s 2026 guide says problems usually trace to slope, hanger spacing or downspout sizing rather than the metal.
In Northern Michigan the stakes are higher. Heavy snowmelt, spring rain and freeze-thaw cycles all push large volumes of water toward the base of the house at once. A downspout that dumps beside the foundation can feed basement seepage and push soil against the wall. Our article on water pooling near your foundation covers the symptoms if you already see them.
Step 1: Decide how many downspouts you need and where
There is no single magic number, but the guidance is consistent. The Building America Solution Center, a U.S. Department of Energy-backed resource, recommends downspouts every 20 to 50 feet and about 1 square inch of downspout cross-section for every 100 square feet of roof area. Snohomish County’s guidance gives the same 20 to 50 foot spacing and limits bends to 45 degrees.
A simple way to apply it:
- Measure each straight gutter run in feet.
- Put one downspout at the low end of each run. The Roofing Brief says downspouts belong at the low end of every slope run, and at outside corners when possible.
- If a run is longer than about 40 feet, add a second downspout and slope the gutter toward each one, high point in the middle.
- Check the roof area each downspout serves. A large roof section draining into one small pipe will overflow in a hard rain.
Where it goes wrong: Valleys and roof intersections concentrate water. A downspout placed far from a valley, or a valley that shoots water over the gutter, overflows no matter how well the pipe is installed. This is why we look at the roof and gutter together. See our roof valley and gutter photo for what that junction looks like.
Step 2: Choose the size and material
Two common sizes are 2×3 inch and 3×4 inch rectangular downspouts, with 4×5 for larger roofs. Angi’s 2026 data shows installed costs of about $6, $8 and $11 per linear foot for those three sizes. Bigger pipe moves more water, which matters on a steep or large roof, and on any roof that drains a long run of gutter.
Materials differ in price and behavior:
| Material | Typical installed cost per linear foot (2026) |
|---|---|
| Vinyl | $6 to $12 |
| Aluminum | $7 to $30 |
| Galvanized steel | $7 to $22 |
| Copper | $23 to $68 |
Those ranges come from Angi’s 2026 cost data. Aluminum is the most common choice for seamless systems because it does not rust and can be matched to your trim color. Match the downspout to the gutter system so the outlet and elbows fit without improvising.
Step 3: Cut the outlet in the gutter
The outlet is the opening where water leaves the gutter and enters the downspout. This Old House’s method: trace the outlet on the upside-down gutter, drill a ¼-inch center hole, and cut the opening with a 4-inch hole saw. Then secure the outlet with four pop rivets or screws.
Where it goes wrong: An outlet that sits slightly high leaves a pool of standing water that freezes and cracks seams. The outlet must be at the lowest point of the run. Gutter Supply’s installation guide says to seal every seam, corner, end cap and outlet with a continuous bead of gutter-rated sealant, not general-purpose silicone, before running water through the system.
Step 4: Set the slope toward the downspout
The gutter has to tilt toward the outlet or water sits. HGTV’s rule for a 30-foot run: divide by 10, multiply by ¼ inch, and you get a ¾-inch drop at the downspout end. Snap a chalk line between your reference marks and hang the gutter to it.
Most slope mistakes happen here, not at the downspout. A gutter that looks level from the ground can hold water along its length. Water that stands all winter turns into ice, adds weight and pulls hangers loose.
Step 5: Build the downspout run
A standard downspout run from the gutter to the ground uses three elbows: two at the top to jog the pipe back to the wall, and one at the bottom to kick water away. Family Handyman notes that each downspout requires three elbows with crimped ends facing down and a 1½-inch overlap at each joint.
The key points:
- Crimp the ends down. The crimped (narrowed) end of each section fits inside the section below it, so water stays inside the pipe instead of leaking at the seam. PEAK Products’ guide calls for overlaps of at least 2 inches between sections and the elbow.
- Dry-fit before you fasten. HGTV advises dry-fitting and drilling pilot holes through both layers, then joining with sheet-metal screws or a rivet gun. Cut with a hacksaw or tin snips.
- Crimp the first elbow slightly with needlenose pliers so it slides into the downspout, as This Old House describes.
Family Handyman’s pros prefer pre-painted 1/4-inch hex head “zipper” screws over rivets because they go in easily and let you take the downspout apart for cleaning.
Step 6: Hold the downspout to the wall
A downspout full of water and ice is heavy. Fasten it to the wall every 6 to 8 feet, as Gutter Supply specifies. PEAK Products says to use two straps for every 10 feet of downpipe, and a good habit is one strap near the top and one near the bottom of each section.
Attach the brackets to the wall first, then set the pipe into them. Drill pilot holes, and use anchors on masonry. On log homes and thick siding, the strap needs a solid fastening point, and spacers can be needed to keep the pipe plumb. We have installed downspouts on log homes, and you can see how the downspout sits against the wall in our project photos.

Where it goes wrong: Straps fastened into trim or soft fascia pull loose after a season of ice. Fastening into solid framing and keeping the pipe plumb prevents most sagging.
Step 7: Send the water away from the house
This last step is the one that protects your basement. The Building America Solution Center says to terminate downspouts at least 5 feet from the foundation, or connect them to an underground catchment system at least 10 feet away. A daylight drain should empty onto sloped grade with a splash block.
The Roofing Brief warns that the most common installation error is dumping discharge onto a splash block within 2 feet of the foundation, which still saturates soil within 4 feet where it can reach the basement. A short elbow and a splash block is the minimum, not the goal.
Surface extensions
A 4-inch extension can carry water to a safe outlet at least 10 feet away and downslope, preferably onto vegetated ground. Choose extensions that stay out of walkways and lawn mowers’ path, and aim them away from your neighbor’s property.
Buried drain lines
If you bury the line, the Building America Solution Center says to slope it at least 0.5 inch per foot away from the house for at least 10 feet. It also warns against connecting the gutter drain pipe to the perforated foundation drain, because that will soak the foundation.
Before you dig anywhere, call 811 so utilities can mark buried lines. This Old House’s dry well guide stresses calling 811 before digging, keeping the well at least 10 feet from the foundation and 3 feet from a property line, and reviewing local excavation rules. Michigan’s frost and clay soils make buried-line slope and depth worth planning with care.

What downspout installation costs
Angi reports a national average of $670 for installing downspouts in 2026, with most homeowners paying $6.50 to $22.25 per linear foot and a total range of $100 to $3,265. These are national figures, published for 2026 and based on material and roof size, so treat them as a starting range, not a local quote.
For a full gutter system, The Roofing Brief puts a typical 200-linear-foot aluminum K-style install at about $1,200 to $2,400, at $6 to $12 per linear foot. What moves your price:
- Height. A two-story downspout takes more pipe, more straps and more ladder work.
- Number of downspouts. More corners and valleys mean more outlets.
- Material and size. Larger pipe and premium metals cost more per foot.
- Drainage. Extensions, splash blocks and buried lines add to the job.
- Removal. Old gutters and downspouts need to come off and be hauled away.
Revive Exteriors does not publish fixed prices for gutter work, because the right system depends on your roof and your lot. We offer complimentary inspections and quotes, and we price each job transparently so you see what goes into it.
Why hire an installer for this
The individual steps above are not mysterious. The trouble is that the steps interact. Outlet height, slope, downspout count, roof valleys, strap fastening and discharge point all have to agree, and a mistake in one shows up in another, often only in the first heavy storm or the first thaw.
That is where a professional installation earns its cost on a Northern Michigan home:
- Seamless gutters are formed to your exact run lengths, so there are fewer seams to leak.
- The downspout count and placement are planned against the whole roof, not one wall at a time.
- Work at height on a second story, over a porch or beside a steep roof is done by a crew that does it every day.
- One project manager keeps the job on schedule and answers your questions.
We provide dedicated project management on every installation, and we install manufacturer-certified products. If you are also looking at the roof, siding or windows, doing the gutters in the same project means the pieces are designed to work together. See our pages on roof replacement and siding.
Our perspective
We think of a downspout as the last line of defense for your foundation. Most of the gutter problems homeowners call us about are not about the metal. They are about where the water goes after it leaves the roof.
That is why we look at the whole picture when we install: the roof edge, the valleys, the number of downspouts, and where each one empties. A seamless gutter with a downspout in the right place, fastened properly and discharging well away from the house, is built to keep working through a Northern Michigan winter.
We are locally owned, we carry an A+ rating from the BBB, and we stand behind our work with a satisfaction promise. That is how we want every installation to be judged.
Jack
Get your downspouts planned and installed
Revive Exteriors installs seamless gutters and downspouts for homeowners in Traverse City, Petoskey, Alpena, Gaylord, Cadillac, Elk Rapids, Charlevoix and Boyne City. We start with a complimentary inspection of your roof edge, gutters and drainage, then give you a clear quote. See the details on our seamless gutter installation page, or look at a recent gutter install.

Call (866) 466-3351 or visit revivemihome.com to schedule. Revive Exteriors, Michigan Lic. #262500123.
FAQ
How far apart should downspouts be?
Plan on one downspout every 20 to 50 feet of gutter, according to the Building America Solution Center. Place each at the low end of a gutter run, and add one where a long run would otherwise overflow. A larger roof area per downspout calls for larger pipe.
How do you hold a downspout in place?
Fasten it to the wall with straps or brackets about every 6 to 8 feet, as Gutter Supply’s guide recommends. Anchor into solid framing or masonry, not loose trim. Keep the pipe plumb so water does not collect at the joints.
How far from the house should a downspout drain?
At least 5 feet from the foundation, or at least 10 feet if the water runs into an underground line, per the Building America Solution Center. The ground should slope away from the house. A splash block right at the wall is not enough.
How much does it cost to install a new downspout?
Angi’s 2026 data shows a national average of $670 for downspout installation, with most jobs at $6.50 to $22.25 per linear foot. Height, material and drainage work change the total. For a Northern Michigan quote, call Revive Exteriors at (866) 466-3351 for a complimentary inspection.
Sources
- Gutters and Downspouts, Building America Solution Center
- Gutters and Downspouts, Snohomish County
- Gutter Installation in 2026: Process + What Goes Wrong, The Roofing Brief
- How Much Does It Cost to Install Downspouts? Angi
- How to Install Rain Gutters, This Old House
- How To Install a Dry Well, This Old House
- How to Install Gutters, HGTV
- Gutter Replacement: How to Install Gutters, Family Handyman
- The Complete Gutter Installation Guide, Gutter Supply
Recommended
- Gutter Install
- Seamless Gutters in Traverse City & Northern MI
- Gutter Replacement Cost: What to Expect in 2026
Revive Exteriors | (866) 466-3351 | revivemihome.com | Michigan Lic. #262500123
